Undercarriage Wear: What Those Tracks Are Really Telling You Before You Buy
On a tracked machine, the undercarriage is where the money is. Engines get the attention, hydraulics get the test, but a worn-out undercarriage on a dozer or excavator can turn a fair-priced machine into an expensive one in a single repair bill. Before you buy, spend real time down at track level — it tells you how the machine was run, how it was maintained, and what you will be paying for next.
Why the undercarriage matters so much
The undercarriage carries the whole machine and takes the worst of the work: rock, mud, frozen ground, and side slopes. On many tracked machines it can account for a large share of the machine's total repair cost over its life. A seller can wash a machine, touch up paint, and tidy the cab in an afternoon. Nobody fakes a healthy undercarriage cheaply. That is why experienced buyers read the tracks first and the paint last.
Check the track chains and pads
Start with the track itself. Look for cracked or bent pads, missing bolts, and pads worn thin at the edges. Run your eye down the chain for dry, rusty pin joints — a sign the sealed lubricant is gone and the pins and bushings are wearing metal on metal. On a machine you can operate, listen as it travels: a clicking or snapping from the tracks at a regular rhythm often points to worn bushings turning on the sprocket.
Excessive track sag matters too. A track adjusted far too tight wears components fast; a track left loose slaps, derails more easily, and chews up rollers. Ask when the tracks were last adjusted and whether tension was checked as part of regular service.
Sprockets, rollers, and idlers tell the maintenance story
Sprocket teeth should be blunt and even, not pointed, hooked, or sharp enough to cut you. Pointed teeth mean the sprocket and chain have been wearing together for a long time — and replacing one without the other usually just speeds up wear on the new part.
Check the bottom rollers for flat spots, leaks at the seals, and uneven wear from side to side. Spin what you can by hand on a smaller machine, or watch them turn while someone travels the machine slowly. Front idlers should run true, without wobble, and the recoil area should be clean — packed mud and debris left sitting there hide leaks and corrosion.
Uneven wear between the left and right sides is information, not just damage. It can point to a machine that spent its life on side slopes, a misaligned frame, or an operator habit the next owner will pay to correct.
Measure, don't guess
Undercarriage wear is measurable, and good sellers expect you to measure it. A simple ultrasonic or caliper check on rail height, bushing diameter, and roller flange wear gives you a percentage of life remaining instead of an opinion. Many dealers will do an undercarriage inspection and give you the numbers in writing.
Those numbers change the deal in a useful way. A machine at 70 per cent undercarriage life is a different purchase from the identical machine at 30 per cent, even at the same hour reading and the same asking price. If a full undercarriage job is coming in the first year you own the machine, that cost belongs in your offer — not as a surprise after the sale.
Match wear to hours and to the story
Finally, cross-check what you see against the hour meter and the service records. Heavy undercarriage wear on a supposedly low-hour machine means one of the stories is wrong: the meter, the records, or the work the machine actually did. Abrasive ground — sand, rock, demolition — wears undercarriages far faster than soft soil, so ask where the machine worked, not just how long.
None of this needs to kill a deal. A worn undercarriage that is priced honestly, with measurements on paper, can be a perfectly good buy. What you want to avoid is paying a low-wear price for a high-wear machine because nobody got down on one knee and looked.
Thinking about a tracked machine and want help judging what the undercarriage is really worth? Talk to Steven Gamsby “The Equipment Guy” at eqguy.ca.
Follow the Equipment Guy Facebook Page for the machines moving across Canada, buying and selling tips, and what’s new at eqguy.ca: https://www.facebook.com/profile.php?id=61595977666634
Follow the Equipment Guy everywhere — and get Let’s Talk Heavy Equipment by email, free on Substack: https://equipmentguy.substack.com · Instagram: https://www.instagram.com/equipmentguy.steve · Threads: https://www.threads.com/@equipmentguy.steve · LinkedIn: https://www.linkedin.com/company/equipment-guy/ · X: https://x.com/StevenGamsby · Pinterest: https://ca.pinterest.com/0ah4vhl7r7q8dx86e44z2b0er1b3ed/
Comments
Post a Comment